Steady air injection upstream of the leading edge was used to increase the surge margin of a centrifugal compressor.To reveal the mechanism,steady numerical simulations were performed on a high pressure ratio centrifugal compressor rotor operated with a rotor tip speed of 586 m/s.Eight different injection yaw angle with four different injection mass flow was performed to determine the configuration that provide the best results for the compression system studied in this work.The injection angle,α,was fifteen degree and the injectors were placed at short distance（ten percent of the inlet tip radius upstream of the compressor face） to achieve maximum control over the leading edge flow by varying individual injection parameters.The results show that at design speed（n=50 000 r/min） with injection flow rate more than 2% of the main flow rate and yaw angle between 20° and 30°,the mass flow rate at stall decreases for approximately 8%.But with higher injection rate,other compressor parameters were affected such as compressor efficiency and compressor total pressure ratio.
A high speed and small mass-flow-rate centrifugal compressor with original and modified volute tongue shape was simulated by 3D viscous Navier-Stokes equations.A sharp and a round tongue of volute were modeled to compare their pressure ratios and efficiency characteristics.The flow fields around volute tongues were investigated;the velocity and pressure distributions of volute inlet were studied by unsteady simulation.Static pressure fluctuation near volute tongue was monitored and transformed into amplitude spectrum to identify blade passing frequency influence.The results show that the tongue simplification can cause certain difference on pressure ratio and efficiency.The pressure and velocity distribution of volute inlet indicate obvious circumferential distortion due to volute tongue especially at low mass flow rate.In addition,the static pressure pulsation of volute inlet and the noise level in diffuser and volute increase significantly under low mass flow operating condition.
Numerical investigation of the unsteady flow variability driven by rotorstator interaction in a transonic axial compressor is performed. Two models with close and far axial gap between rotor and stator rows are studied in the simulation. Particular attention is attached to the analysis of mechanisms involved in driving rotor wake oscillation, rotor wake skewing and flow angle fluctuation at rotor exit. The results show that smaller axial gap is favorable to enhance the interaction in the region between two adjacent rows, and the fluctuation of the static pressure difference between two sides of rotor wake is improved by potential field from down stator, which is the driving force for rotor wake oscillation. The interaction between rotor and stator is weakened by increasing axial distance, rotor wake shifts to suction side of rotor blade with 5%-10% of rotor pitch, the absolute value of flow angle at rotor exit is less than that in the case of close interspace for every time step, and the fluctuation amplitude is also decreased.
The superimposed influences of the blade rows in a multistage compressor are important because different matches of upstream and downstream blades can result in significant differences in the stator wake oscillation. Numerical investigation of the axial stator wake oscillation, which is affected upstream by the axial rotor and downstream by the radial rotor, was performed in an axial-radial combined compressor. Many configurations with different blade numbers and locations, which influence axial stator wake oscillation were investigated. When rotors have equal blade numbers, the axial stator wake oscillates periodically versus time within time T(moving blade passing 1/3 revolution). In contrast, stator wake oscillates irregularly within T when rotors have different blade numbers. A model-split subtraction method is presented in order to separate the influences of the individual blade rows on the wake oscillation of the axial stator. Analysis from the rotor-stator configuration showed that the unsteady flow angle fluctuation response is caused by the upstream rotor. For the rotor-stator-rotor configuration, the unsteady flow angle fluctuations are influenced by upand downstream blade rows. With the model-split subtraction method, the upand downstream influences on the flow angle fluctuation could be clearly separated and quantified. Low amplitudes could be observed when the influences from upand downstream moving rows were superimposed with the "positive peaknegative peak" type wave. Clocking investigations were carried out to change the relative superimposed phase of influences from the surrounding blade rows in order to modulate the amplitudes of the axial stator wake oscillation. However, the amplitudes did not reach the maximum when they were superimposed with "positive peak-positive peak" type wave due to the impact of the interaction between the two moving blade rows.
